Instytut Podstawowych Problemów Techniki
Polskiej Akademii Nauk

Partnerzy

K. Kowiorski


Ostatnie publikacje
1.  Nosewicz S., Jenczyk P., Romelczyk-Baishya B., Bazarnik P., Jarząbek D.M., Majchrowicz K., Pakieła Z., Kowiorski K., Chmielewski M., The influence of spark plasma sintering on multiscale mechanical properties of nickel-based composite materials, MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, ISSN: 0921-5093, DOI: 10.1016/j.msea.2023.146001, Vol.891, pp.146001, 2024

Streszczenie:
The paper presents a comprehensive investigation of the influence of the main process parameters of spark plasma sintering on the mechanical and microstructural properties of nickel-silicon carbide composites at various scales. Microstructure analysis performed by scanning and transmission electron microscopy revealed a significant interfacial reaction between nickel and silicon carbide due to the decomposition of silicon carbide. The chemical interaction of the matrix and reinforcement results in the formation of a multicomponent interphase zone formed by silicides (Ni31Si12 or/and Ni3Si) and graphite precipitates. Furthermore, several types of structure defects were observed (mainly nano/micropores at the phase boundaries). These significantly influenced the mechanical response of nickel-silicon carbide composites at different levels. At the macroscopic scale, uniaxial tensile tests confirmed that applying a 1000 oC sintering temperature ensured that the manufactured composite was characterised by satisfactory tensile strength, however, with a considerable reduction of material elongation compared to pure nickel. Moreover, the fractography study allowed us to identify a significant difference in the damage mode for certain nickel-silicon carbide samples. Secondly, the interface of the nickel matrix and silicate interphase was tested by bending with microcantilevers to evaluate its deformation behaviour, strength, and fracture characteristics. It was confirmed that a diffusive kind of interface, such as Ni-NiSi, demonstrates unexpected bonding properties with a relatively large range of plastic deformation. Finally, the nanoindentation of three main components of the nickel-silicon carbide composite was executed to evaluate the evolution of nanohardness, Young’s modulus, and elastic recovery due to the application of various spark plasma sintering conditions.

Słowa kluczowe:
nickel-based composite,silicon carbide,spark plasma sintering,multiscale characterization,mechanical properties,nanoindentation,bending of microcantilevers

Afiliacje autorów:
Nosewicz S. - IPPT PAN
Jenczyk P. - IPPT PAN
Romelczyk-Baishya B. - Politechnika Warszawska (PL)
Bazarnik P. - Politechnika Warszawska (PL)
Jarząbek D.M. - IPPT PAN
Majchrowicz K. - inna afiliacja
Pakieła Z. - Politechnika Warszawska (PL)
Kowiorski K. - inna afiliacja
Chmielewski M. - Institute of Electronic Materials Technology (PL)
140p.
2.  Kowiorski K., Heljak M., Strojny-Nędza A., Bucholc B., Chmielewski M., Djas M., Kaszyca K., Zybała R., Małek M., Swieszkowski W., Chlanda A., Compositing graphene oxide with carbon fibers enables improved dynamical thermomechanical behavior of papers produced at a large scale, , DOI: 10.1016/j.carbon.2023.02.009, Vol.206, pp.26-36, 2023

Streszczenie:
This article discusses the morphology and thermomechanical properties of graphene oxide (GO) paper sheets and GO paper composites reinforced with carbon fibers. GO paper was fabricated using GO paste obtained by the condensation of GO aqueous solution synthesized using the Hummers' method. Carbon fibers were implemented to improve the mechanical properties of the pristine GO paper. All the investigated papers were subjected to thermal treatment to check thermo-related morphological and mechanical properties. The results presented in this study allowed for the deeper insight into morphological, structural, and mechanical volume and surface-related properties of pristine GO and GO-based composite materials reinforced with carbon fibers. We showed that there are two important factors that should be taken into consideration for the design and fabrication of GO-based papers. These factors were the concentration of the reinforcing agent and the thermal reduction of the papers. Both factors have influenced the final properties of the resulting GO-based papers. For the first time, it was revealed how the addition of the reinforcing material affects the GO paper thermal expansion coefficient.

Słowa kluczowe:
Flake graphene, Graphene oxide, Graphene oxide paper, Carbon fibers, Mechanical properties

Afiliacje autorów:
Kowiorski K. - inna afiliacja
Heljak M. - Politechnika Warszawska (PL)
Strojny-Nędza A. - Institute of Electronic Materials Technology (PL)
Bucholc B. - IPPT PAN
Chmielewski M. - Institute of Electronic Materials Technology (PL)
Djas M. - inna afiliacja
Kaszyca K. - Lukasiewicz Institute of Microelectronics and Photonics (PL)
Zybała R. - Politechnika Warszawska (PL)
Małek M. - inna afiliacja
Swieszkowski W. - inna afiliacja
Chlanda A. - Politechnika Warszawska (PL)
3.  Zybała R., Bucholc B., Kaszyca K., Kowiorski K., Soboń D., Żórawski W., Moszczyńska D., Molak R., Pakieła Z., Properties of Cold Sprayed Titanium and Titanium Alloy Coatings after Laser Surface Treatment , Materials, ISSN: 1996-1944, DOI: 10.3390/ma15249014, Vol.15(24), No.9014, pp.1-17, 2022

Streszczenie:
Additive manufacturing (AM) has seen remarkable development in recent years due to relatively high efficiency of the process. Cold spraying (CS) is a particular method of AM, in which titanium and titanium alloy powders are used. CS is a very competitive technology enabling the deposition of coatings, repairing machine parts, and manufacturing new components. For specific applications, the surface of cold-sprayed materials may require further processing. This paper reports an attempt to employ laser surface treatment (LST) of cold-sprayed coatings on an aluminium alloy substrate. The influence of laser beam interaction time on the coatings’ properties was analysed. The microstructure was investigated and observed employing scanning electron microscopy (SEM). To evaluate residual stress after CS and LST, the sin2ψ technique was used. Investigations were also performed on Vickers hardness, contact angle, and surface roughness. Significant changes in the surface morphology of the coatings and elevated residual stress levels dependent on the laser beam interaction time were observed. Increased Vickers hardness was recorded for titanium alloy Ti6Al4V. LST also led to increased surface hydrophilicity of the modified materials Ti and Ti6Al4V.

Słowa kluczowe:
cold spray, laser surface treatment, titanium coating, Ti6Al4V, residual stresses

Afiliacje autorów:
Zybała R. - Politechnika Warszawska (PL)
Bucholc B. - IPPT PAN
Kaszyca K. - Lukasiewicz Institute of Microelectronics and Photonics (PL)
Kowiorski K. - inna afiliacja
Soboń D. - inna afiliacja
Żórawski W. - inna afiliacja
Moszczyńska D. - inna afiliacja
Molak R. - inna afiliacja
Pakieła Z. - Politechnika Warszawska (PL)
140p.
4.  Bucholc B., Kaszyca K., Śpiewak P., Marszałek K., Kruszewski M., Ciupiński Ł., Kowiorski K., Zybała R., Thermoelectric properties of bismuth-doped magnesium silicide obtained by the self-propagating high-temperature synthesis, BULLETIN OF THE POLISH ACADEMY OF SCIENCES: TECHNICAL SCIENCES, ISSN: 0239-7528, DOI: 10.24425/bpasts.2022.141007, Vol.70(3), No.e141007, pp.1-7, 2022

Streszczenie:
Doping is one of the possible ways to significantly increase the thermoelectric properties of many different materials. It has been confirmed that by introducing bismuth atoms into Mg sites in the Mg2Si compound, it is possible to increase career concentration and intensify the effect of phonon scattering, which results in remarkable enhancement in the figure of merit (ZT) value. Magnesium silicide has gained scientists’ attention due to its nontoxicity, low density, and inexpensiveness. This paper reports on our latest attempt to employ ultrafast selfpropagating high-temperature synthesis (SHS) followed by the spark plasma sintering (SPS) as a synthesis process of doped Mg2Si. Materials with varied bismuth doping were fabricated and then thoroughly analyzed with the laser flash method (LFA), X-ray diffraction (XRD), scanning electron microscopy (SEM) with an integrated energy-dispersive spectrometer (EDS). For density measurement, the Archimedes method was used. The electrical conductivity was measured using a standard four-probe method. The Seebeck coefficient was calculated from measured Seebeck voltage in the sample subjected to a temperature gradient. The structural analyses showed the Mg2Si phase as dominant and Bi2Mg3 located at grain boundaries. Bismuth doping enhanced ZT for every dopant concentration. ZT = 0:44 and ZT=0.38 were obtained for 3wt% and 2wt% at 770 K, respectively.

Słowa kluczowe:
thermoelectric materials, magnesium silicide, bismuth doping, SHS, spark plasma sintering

Afiliacje autorów:
Bucholc B. - IPPT PAN
Kaszyca K. - Lukasiewicz Institute of Microelectronics and Photonics (PL)
Śpiewak P. - inna afiliacja
Marszałek K. - AGH University of Science and Technology (PL)
Kruszewski M. - inna afiliacja
Ciupiński Ł. - Politechnika Warszawska (PL)
Kowiorski K. - inna afiliacja
Zybała R. - Politechnika Warszawska (PL)
100p.

Abstrakty konferencyjne
1.  Nosewicz S., Jenczyk P., Jarząbek D., Strojny-Nędza A., Kaszyca K., Kowiorski K., Bazarnik P., Pakieła Z., Romelczyk Baishya B., Chmielewski M., Multiscale investigation of microstructural and mechanical properties of spark plasma sintered Ni-SiC composites, AMT'2023, Advanced Materials and Technologies Conference, 2023-06-18/06-21, Wisła (PL), pp.1, 2023

Streszczenie:
In the case of the sintering of composite materials exhibiting mutual solubility, intermediate phases with varying concentrations of elements may appear during the densification process. Microstructural and structural changes, especially in the area of the interface, strongly influence mechanical or thermal properties [1]. A good example of such materials is nickel – silicon carbide composites. At elevated temperatures nickel reacts with silicon carbide, which causes total SiC decomposition, and as a result, new Ni-Si phases are formed and free carbon is precipitated within the reaction zone. In this work, nickel-silicon carbide composites were obtained via the Spark Plasma Sintering method. The detailed microstructural analyses using X-ray diffraction, Raman spectroscopy, scanning electron microscopy and transmission electron microscopy revealed the material’s evolution during sintering. To investigate the correlation between microstructure and properties of obtained materials, the mechanical test at three different length scales (in macro-, micro- and nanoscale) was conducted. To evaluate the strength of Ni-SiC composites at a macroscopic scale the uniaxial tensile and compression tests were employed. The sample deformation and failure mechanism for different stages of sintering were analyzed. The strength of the nickel-silicon carbide interface was determined by bending tests of micro-cantilever beams. Nanoindentation was used to evaluate the hardness of each composite component. The conducted research revealed a strong relation between mechanical strength and sintering conditions.

Afiliacje autorów:
Nosewicz S. - IPPT PAN
Jenczyk P. - IPPT PAN
Jarząbek D. - IPPT PAN
Strojny-Nędza A. - Institute of Electronic Materials Technology (PL)
Kaszyca K. - Lukasiewicz Institute of Microelectronics and Photonics (PL)
Kowiorski K. - inna afiliacja
Bazarnik P. - Politechnika Warszawska (PL)
Pakieła Z. - Politechnika Warszawska (PL)
Romelczyk Baishya B. - inna afiliacja
Chmielewski M. - Institute of Electronic Materials Technology (PL)

Kategoria A Plus

IPPT PAN

logo ippt            ul. Pawińskiego 5B, 02-106 Warszawa
  +48 22 826 12 81 (centrala)
  +48 22 826 98 15
 

Znajdź nas

mapka
© Instytut Podstawowych Problemów Techniki Polskiej Akademii Nauk 2024