Instytut Podstawowych Problemów Techniki
Polskiej Akademii Nauk

Partnerzy

M.J. Kruszewski


Ostatnie publikacje
1.  Zgłobicka I., Dobkowska A., Zielińska A., Borucińska E., Kruszewski M., Zybała R., Płociński T., Idaszek J., Jaroszewicz J., Paradowski K., Adamczyk-Cieślak B., Nikiforow K., Bucholc B., Święszkowski W., Kurzydłowski K., In-depth analysis of the influence of bio-silica filler ( Didymosphenia geminata frustules) on the properties of Mg matrix composites, Journal of Magnesium and Alloys, ISSN: 2213-9567, DOI: 10.1016/j.jma.2023.08.001, Vol.11, pp.2853-2871, 2023

Streszczenie:
A novel metal matrix composites (MMC) with Mg matrix reinforced with natural filler in the form of Didymosphenia geminata frustules (algae with distinctive siliceous shells) are presented in this work. Pulse plasma sintering (PPS) was used to manufacture Mg-based composites with 1, 5 and 10 vol.% ceramic filler. As a reference, pure Mg was sintered. The results show that the addition of 1 vol.% Didymosphenia geminata frustules to the Mg matrix increases its corrosion resistance by supporting passivation reactions, and do not affect the morphology of L929 fibroblasts. Addition of 5 vol.% the filler does not cause cytotoxic effects, but it supports microgalvanic reactions leading to the greater corrosion rate. Higher content than 5 vol.% the filler causes significant microgalvanic corrosion, as well as increases cytotoxicity due to the greater micro-galvanic effect of the composites containing 10 and 15 vol.% diatoms. The results of contact angle measurements show the hydrophilic character of the investigated materials, with slightly increase in numerical values with addition of amount of ceramic reinforcement. The addition of Didymosphenia geminata frustules causes changes in a thermo-elastic properties such as mean apparent value of coefficient of thermal expansion (CTE) and thermal conductivity (λ). The addition of siliceous reinforcement resulted in a linear decrease of CTE and reduction in thermal conductivity over the entire temperature range. With the increasing addition of Didymosphenia geminata frustules, an increase in strength with a decrease in compressive strain is observed. In all composites an increase in microhardness was attained.
The results clearly indicate that filler in the form of Didymosphenia geminata frustules may significantly change the most important properties of pure Mg, indicating its wide potential in the application of Mg-based composites with a special focus on biomedical use.

Słowa kluczowe:
Metal-matrix composites (MMCs),Pulse plasma sintering (PPS),Ceramic filler,Microstructure,Properties

Afiliacje autorów:
Zgłobicka I. - inna afiliacja
Dobkowska A. - inna afiliacja
Zielińska A. - inna afiliacja
Borucińska E. - inna afiliacja
Kruszewski M. - inna afiliacja
Zybała R. - Politechnika Warszawska (PL)
Płociński T. - Politechnika Warszawska (PL)
Idaszek J. - inna afiliacja
Jaroszewicz J. - inna afiliacja
Paradowski K. - inna afiliacja
Adamczyk-Cieślak B. - inna afiliacja
Nikiforow K. - inna afiliacja
Bucholc B. - IPPT PAN
Święszkowski W. - inna afiliacja
Kurzydłowski K. - inna afiliacja
100p.
2.  Bucholc B., Kaszyca K., Śpiewak P., Marszałek K., Kruszewski M., Ciupiński Ł., Kowiorski K., Zybała R., Thermoelectric properties of bismuth-doped magnesium silicide obtained by the self-propagating high-temperature synthesis, BULLETIN OF THE POLISH ACADEMY OF SCIENCES: TECHNICAL SCIENCES, ISSN: 0239-7528, DOI: 10.24425/bpasts.2022.141007, Vol.70(3), No.e141007, pp.1-7, 2022

Streszczenie:
Doping is one of the possible ways to significantly increase the thermoelectric properties of many different materials. It has been confirmed that by introducing bismuth atoms into Mg sites in the Mg2Si compound, it is possible to increase career concentration and intensify the effect of phonon scattering, which results in remarkable enhancement in the figure of merit (ZT) value. Magnesium silicide has gained scientists’ attention due to its nontoxicity, low density, and inexpensiveness. This paper reports on our latest attempt to employ ultrafast selfpropagating high-temperature synthesis (SHS) followed by the spark plasma sintering (SPS) as a synthesis process of doped Mg2Si. Materials with varied bismuth doping were fabricated and then thoroughly analyzed with the laser flash method (LFA), X-ray diffraction (XRD), scanning electron microscopy (SEM) with an integrated energy-dispersive spectrometer (EDS). For density measurement, the Archimedes method was used. The electrical conductivity was measured using a standard four-probe method. The Seebeck coefficient was calculated from measured Seebeck voltage in the sample subjected to a temperature gradient. The structural analyses showed the Mg2Si phase as dominant and Bi2Mg3 located at grain boundaries. Bismuth doping enhanced ZT for every dopant concentration. ZT = 0:44 and ZT=0.38 were obtained for 3wt% and 2wt% at 770 K, respectively.

Słowa kluczowe:
thermoelectric materials, magnesium silicide, bismuth doping, SHS, spark plasma sintering

Afiliacje autorów:
Bucholc B. - IPPT PAN
Kaszyca K. - Lukasiewicz Institute of Microelectronics and Photonics (PL)
Śpiewak P. - inna afiliacja
Marszałek K. - AGH University of Science and Technology (PL)
Kruszewski M. - inna afiliacja
Ciupiński Ł. - Politechnika Warszawska (PL)
Kowiorski K. - inna afiliacja
Zybała R. - Politechnika Warszawska (PL)
100p.
3.  Zybała R., Schmidt M., Kaszyca K., Ciupiński Ł., Kruszewski M.J., Pietrzak K., Method and Apparatus for Determining Operational Parameters of Thermoelectric Modules, Journal of Electronic Materials, ISSN: 0361-5235, DOI: 10.1007/s11664-016-4712-1, Vol.45, No.10, pp.5223-5231, 2016

Streszczenie:
The main aim of this work was to construct and test an apparatus for characterization of high temperature thermoelectric modules to be used in thermoelectric generator (TEGs) applications. The idea of this apparatus is based on very precise measurements of heat fluxes passing through the thermoelectric (TE) module, at both its hot and cold sides. The electrical properties of the module, under different temperature and load conditions, were used to estimate efficiency of energy conversion based on electrical and thermal energy conservation analysis. The temperature of the cold side, Tc, was stabilized by a precise circulating thermostat (≤0.1°C) in a temperature range from 5°C to 90°C. The amount of heat absorbed by a coolant flowing through the heat sink was measured by the calibrated and certified heat flow meter with an accuracy better than 1%. The temperature of the hot side, Th, was forced to assumed temperature (Tmax = 450°C) by an electric heater with known power (Ph = 0–600 W) with ample thermal insulation. The electrical power was used in calculations. The TE module, heaters and cooling plate were placed in an adiabatic vacuum chamber. The load characteristics of the module were evaluated using an electronically controlled current source as a load. The apparatus may be used to determine the essential parameters of TE modules (open circuit voltage, Uoc, short circuit current, Isc, internal electrical resistance, Rint, thermal resistance, Rth, power density, and efficiency, η, as a function of Tc and Th). Several commercially available TE modules based on Bi2Te3 and Sb2Te3 alloys were tested. The measurements confirmed that the constructed apparatus was highly accurate, stable and yielded reproducible results; therefore, it is a reliable tool for the development of thermoelectric generators.

Słowa kluczowe:
energy conversion efficiency, power generation, thermoelectric modules, performance characterization, heat recovery, renewable energy

Afiliacje autorów:
Zybała R. - Politechnika Warszawska (PL)
Schmidt M. - Institute of Electronic Materials Technology (PL)
Kaszyca K. - Lukasiewicz Institute of Microelectronics and Photonics (PL)
Ciupiński Ł. - Politechnika Warszawska (PL)
Kruszewski M.J. - inna afiliacja
Pietrzak K. - inna afiliacja
25p.

Kategoria A Plus

IPPT PAN

logo ippt            ul. Pawińskiego 5B, 02-106 Warszawa
  +48 22 826 12 81 (centrala)
  +48 22 826 98 15
 

Znajdź nas

mapka
© Instytut Podstawowych Problemów Techniki Polskiej Akademii Nauk 2024