Partners

Abstract:
A nonplanar polylactide scaffold to be used in tissue engineering was obtained by freeze‐extraction method. Properties of the scaffold were modified by adding Eudragit® E100. The impact of the modification on morphology, porosity and pore size, mass absorbability, mechanical properties was determined. Scanning electron microscopy (SEM), hydrostatic weighing test, static compression test was used to this end. The chemical composition of the scaffold was defined based on infrared spectroscopy (FTIR) and energy‐dispersive X‐ray spectroscopy (EDX). Biocompatibility was confirmed by quantitative tests and microscopic observation. The obtained results show that the obtained scaffolds may be applied as a carrier of hydrophilic cellular growth factors for more efficient tissue regeneration.

Keywords:
cellular studies, Eudragit® E100, freeze-extraction, poly-L-lactide

Abstract:
Implants in the form of polymer scaffolds are commonly used to regenerate bone tissue after traumas or tooth extractions. However, few implant formation methods enable building polymer scaffolds allowing to reconstruct larger bone losses without immune response. Spacious, porous poly-l-lactide implants with considerable volume were obtained using the phase inversion method with the freeze-extraction variant. The calcium phosphate (CaP) coating was deposited on implant surfaces with the biomimetic method to improve the implant's osteoconductivity. The substitues morphology was characterized-porosity, size and shape of pores; mechanical properties, mass absorbability of implants before and after mineralization. The characteristics were provided with scanning electron microscopy (SEM), static compression test and hydrostatic weighing, respectively. The presence of CaPs in the entire volume of the implant was confirmed with SEM and infrared spectroscopy with Fourier transform (FTIR). The biocompatibility of scaffolds was confirmed with in vitro quantitative test and microscopic observations. The obtained results show that the implants can be used in tissue engineering as a vehicle of platelet-rich plasma to regenerate critical spongy bone losses.

Keywords:
bone graft, calcium phosphate(s), cell culture

Abstract:
Results of the preparation of biodegradable porous scaffolds using an original modification of a wet phase inversion method were presented. Influence of gelatin non‐woven as a non‐classic pore precursor and polyvinylpyrrolidone, Pluronic as classic pore precursors on the structure of obtained scaffolds was analyzed. It was shown that the addition of gelatin non‐wovens enables the preparation of scaffolds, which allow for the growth of cells (size, distribution, and shape of pores). Mechanical properties of the obtained cell scaffolds were determined. The influence of pore precursors on mass absorption of scaffolds against isopropanol and plasma was investigated. Interaction of scaffolds with a T‐lymphocyte line (Jurkat) and with fibroblasts (L929) was investigated. Obtained scaffolds are not cytotoxic and can be used as implants, for example, the regeneration of cartilage tissue.

Keywords:
cell cultures, cytotoxic, fibroblasts, imprinted scaffolds

Abstract:
The main goal of tissue engineering (TE) is supporting the regeneration of damaged tissues that are difficult to regenerate. The experimental results of the preparation of semi-permeable membranes for cell cultures are presented. The effect of the PLA molecular weight and addition of pore precursors on the morphology of the membranes was studied. The pore precursor of choice was polyvinylpyrrolidone (PVP). It was found that semi-permeable membranes for application in tissue engineering can be prepared with polylactides of molecular weight more significant than 37,000 g/mol. Moreover, it was observed that the growth of the molecular weight of the polymer, the porosity, the size of the pores, the Young modulus and maximum tensile increased. Additionally, to obtain a better morphology of the membranes, PVP should be added to the polymeric solution. Positive growth of L929 fibroblast cells on the obtained scaffolds was shown.

Keywords:
biodegradable polymers, cell cultures, L929 fibroblasts, polylactide, scaffolds, tissue engineering

Abstract:
Polyester 3D scaffolds were obtained by dry inversion phase method. The influence of a polymer and liquid pore precursor type on the 3D scaffolds morphology, porosity and mechanical properties was tested. Polymers and precursors forming a porous structure were identified. It was found that 3D scaffolds having the most preferable structure for cell cultures were obtained from polylactide with the addition of n‐butanol as the liquid pore precursor.

Keywords:
liquid pore precursors, mechanical properties, dry inversion phase method, 3D scaffolds

Abstract:
Zbadano wpływ dodatku ciekłych prekursorów porów na morfologię, porowatość i właściwości mechaniczne polilaktydowych rusztowań komórkowych. Rusztowania otrzymano metodą mokrej inwersji faz w wariancie freeze extraction. Oceniono cytotoksyczność wybranych rusztowań w stosunku do fibroblastów mysich oraz ich przydatność do hodowli komórkowych. Wykazano, że dodatek prekursora porów dopolilaktydu korzystnie zmienia morfologię wytworzonych rusztowań, jednocześnie pogarszając ich wytrzymałość mechaniczną. Stwierdzono, że polilaktydowe rusztowania komórkowe z powodzeniem mogą być wykorzystywane do hodowli komórkowych.

Keywords:
usztowania komórkowe, polilaktyd, hodowle komórkowe, fibroblasty

Abstract:
Results of the preparation of semi-permeable membranes made of biodegradable polymers membranes were presented. Among known polyesters, polylactide was selected for research. The membranes were obtained using wet phase inversion method. The influence of polyvinylpyrrolidone and polymeric nano-non-wovens as pores precursors on the structure of obtained membranes was analysed. It was shown, that utilisation of polymeric nano-non-wovens enabled preparation of semi-permeable membranes, which could be used as wide-pore 3D-type cellular scaffolds.

Keywords:
Biodegradable polymers membranes, Biodegradable polyesters, Porous three-dimensional scaffolds, Inversion phase method